ISO 5011:2025: How Air-Cleaner Testing Separates Restriction, Efficiency and Dust Capacity
The fifth edition of ISO 5011 compares inlet air cleaners through restriction, collection efficiency and dust capacity, with defined test objects and terminal conditions; capacity no longer depends on the precleaner's scavenge flow rate.
ISO 5011:2025 treats an inlet air cleaner as a measured assembly rather than a generic filter label. The fifth edition, published in September 2025 as a 50-page replacement for the 2020 edition, defines laboratory procedures for comparing air cleaners used on internal combustion engines and compressors. It separates airflow resistance, particle collection and contaminant-holding capacity, and it defines what constitutes the unit under test. Its purpose is comparison under stated conditions, not a field-performance guarantee for a compressor package.
What changed in the fifth edition?
ISO records four changes: capacity is no longer dependent on scavenge flow rate, “air cleaner” replaces “air filter” where appropriate, the symbols list was edited, and Annex H received significant editorial modifications.
The capacity change is the clearest technical revision. A precleaner can remove collected dust through a scavenged airflow, but the fifth edition no longer makes the capacity result dependent on that flow-rate condition in the way the previous edition did. The public foreword identifies the change without publishing the complete revised procedure.
The terminology change also matters. The document's subject is the air-cleaner assembly and its elements, not merely a sheet of filter media. That language aligns the title, definitions and test object.
The remaining changes concern symbols and editorial organisation. They should not be presented as new performance thresholds.
Which performance quantities does the test separate?
The standard separates restriction or differential pressure, dust-collection efficiency, dust capacity and oil carry-over on oil-bath cleaners because each answers a different operating question.
Restriction is the static pressure measured immediately downstream of the unit under test. Differential pressure compares static pressure immediately upstream and downstream. Pressure loss corrects that difference for any difference in dynamic head at the measuring points.
Efficiency describes the unit's ability to remove contaminant mass under specified test conditions. It does not describe how much contaminant the unit can hold before reaching its endpoint.
Capacity is the quantity of contaminant removed by the unit while producing specified terminal conditions. A cleaner can therefore have a high efficiency at one point and still reach its terminal condition with a different amount of collected dust.
Oil carry-over applies to oil-bath air cleaners and records the appearance of oil at the outlet. It is not another name for particle penetration.
| Quantity | Question answered |
|---|---|
| Restriction or differential pressure | How much resistance does the cleaner introduce at the test airflow? |
| Efficiency | How much of the contaminant mass is collected under the stated conditions? |
| Capacity | How much contaminant is collected before the terminal condition occurs? |
| Oil carry-over | Does oil appear at the outlet of an oil-bath cleaner? |
What counts as the unit under test?
The unit under test can be a single filter element or a complete air-cleaner assembly, and the distinction determines what the result represents.
A filter element is the replaceable part consisting of filter material and its carrying frame. A complete assembly may also include a precleaner and more than one element. Testing an element alone does not measure the complete assembly's housing, sealing or airflow arrangement.
A single-stage cleaner has no separate precleaner. A multistage cleaner has two or more stages, commonly with a precleaner followed by one or more filter elements. Where two elements are present, the first is the primary element and the second is the secondary element.
The secondary element sits downstream of the primary element. Its stated role is protection against dust during certain primary-element failures or while the primary element is removed for service. That role is different from a second independent efficiency claim for the complete assembly.
How do airflow and terminal conditions frame the result?
Airflow defines the test point, and the terminal condition defines when the test ends; neither can be omitted from a comparison.
Test airflow is the quantity of air passing through the cleaner outlet per unit time, corrected to standard conditions. Rated airflow is specified by the user or manufacturer and may be used as the test airflow. Scavenged airflow is the airflow used to remove collected dust from a precleaner, expressed as a percentage of test airflow.
A terminal condition can occur when restriction or differential pressure reaches an agreed value, when efficiency or another performance parameter falls to an agreed value, when oil carry-over occurs, or when a dust pot becomes full. These alternatives make the endpoint an explicit part of the test record.
Capacity reported without a terminal condition is incomplete. Efficiency reported without the test airflow and contaminant conditions is incomplete. Restriction reported without its measurement location is incomplete. The standard's definitions make those dependencies visible.
Which reference documents control dust and pressure measurement?
ISO 5011 links the comparison to standard test contaminants and established differential-pressure measurement rather than allowing each laboratory to choose unrelated inputs.
ISO 12103-1 specifies Arizona test dust for filter evaluation. ISO 5167-1 provides general principles and requirements for differential-pressure devices in full, circular conduits. These references do not replace ISO 5011's air-cleaner procedure; they support the consistency of its inputs and measurements.
The bibliography also separates fractional-efficiency testing. ISO/TS 19713-1 addresses fine particles from 0.3 µm to 5 µm optical diameter, while ISO/TS 19713-2 addresses coarse particles from 5 µm to 40 µm. Those particle-resolved methods should not be confused with the overall efficiency and capacity comparison described in ISO 5011.
The result is a test chain in which the dust, airflow, pressure measurement and test object all have identities. Changing one of them changes the basis of comparison.
Why does air-cleaner performance not equal compressor performance?
The air cleaner influences the compressor's inlet condition, but ISO 5011 does not measure the compressor's flow, power, efficiency or guarantee performance.
A restriction result describes the cleaner at its test airflow. It does not, on its own, quantify the compressor's capacity or specific-power change. A collection-efficiency result describes contaminant removal by the cleaner. It does not establish wear, reliability or maintenance intervals for the compressor.
That boundary is particularly important for process-gas packages. The standard applies to air cleaners used on engines and compressors in automotive and industrial applications, but it does not turn the test into a process-gas compatibility or hazardous-area assessment.
ISO 5011 therefore belongs upstream of the compressor's performance record. It can support an inlet-equipment comparison; the machine's guarantee still requires its own test code and operating data.
Why are the pressure terms not interchangeable?
Restriction, differential pressure and pressure loss use related measurements but answer different definitions, so they cannot be substituted in a test report.
Restriction is measured immediately downstream of the test unit. Differential pressure uses the static-pressure difference between immediately upstream and downstream locations. Pressure loss goes further by correcting for a difference in dynamic head at those measuring points.
A single negative static-pressure reading is therefore not automatically the complete pressure-loss result. The measurement locations and any dynamic-head correction belong to the reported method.
These definitions also explain why restriction and efficiency should be read separately. One describes the cleaner's effect on airflow conditions; the other describes its removal of contaminant mass. Neither supplies the other's value.
Why is the test dust part of the result's identity?
The contaminant used in the test determines what the efficiency and capacity results mean, so the dust specification belongs beside the numerical result.
ISO 5011 references ISO 12103-1 for Arizona test dust used in filter evaluation. That common reference prevents a result obtained with one contaminant from being treated as directly equivalent to a result obtained with an unrelated material.
Particle size adds another layer. ISO/TS 19713-1 covers fractional-efficiency testing with fine particles from 0.3 µm to 5 µm optical diameter, while ISO/TS 19713-2 covers coarse particles from 5 µm to 40 µm. A particle-resolved result across those ranges is different from an overall collection-efficiency figure.
The same reasoning applies to capacity. The mass collected before the terminal condition is linked to the contaminant introduced during the test. Dust type, test airflow and terminal condition therefore form part of the result rather than optional laboratory metadata.
Where does the public record stop?
The public preview provides the revision notes, scope, definitions and reference structure, but the detailed apparatus, procedures and calculation requirements remain in the standard text.
The fifth edition's capacity change is publicly documented, yet its implementation cannot be reconstructed from the foreword alone. The full text must be used when establishing a test method or reviewing a laboratory report.
The public record also does not establish field dust loading, maintenance intervals or compressor degradation for any installation. Those are operational questions outside a laboratory comparison.
What does the fifth edition add up to?
ISO 5011:2025 makes an air-cleaner comparison traceable through four separable results: resistance, efficiency, capacity and, where applicable, oil carry-over. It also identifies the test object, airflow, contaminant and terminal condition behind those results.
The revision does not make one cleaner universally preferable. It makes the evidence easier to compare without turning a filter-element result into a complete-compressor claim.
What this article does not cover
Note that this article does not reproduce ISO 5011's apparatus or procedures, calculate compressor performance, specify a maintenance interval, or assess a filter or compressor model. It records the standard's public scope and revision logic and is not a conformity determination.
Where the next constraint sits
The compressor-family decision and the gas it handles come before inlet-equipment comparison: Specialty Gas Compressor Selection Guide: From Gas to Machine Type.
The separate question of whether the complete compressor meets its performance guarantee is covered in ASME PTC 10-2022: The Rulebook for "Does the Machine Meet Its Guarantee" Was Rebuilt After 25 Years.
Sources
| # | Basis |
|---|---|
| 1 | ISO 5011:2025, Inlet air cleaning equipment for internal combustion engines and compressors — Performance testing, Edition 5, published 2025-09, 50 pages; the laboratory-comparison scope and the restriction, efficiency, capacity and oil-carry-over measurements — the official ISO catalogue page, https://www.iso.org/standard/85950.html |
| 2 | The replacement of ISO 5011:2020; the capacity, terminology, symbols and Annex H revision notes; the test-object, airflow, pressure and terminal-condition definitions; the ISO 12103-1 and ISO 5167-1 references; the separate fractional-efficiency documents and their particle ranges — the ISO Online Browsing Platform public preview, https://www.iso.org/obp/ui/en/#!iso:std:85950:en |